Leave Your Message
Raspberry Pi HAT: Premium Expansion Boards from China Suppliers for Factory-Grade Projects and IoT Solutions
Hot Products
Products Categories
Featured Products

Raspberry Pi HAT: Premium Expansion Boards from China Suppliers for Factory-Grade Projects and IoT Solutions

The Raspberry Pi is an affordable mini single-board computer created by the Raspberry Pi Foundation in the UK. Renowned for its compact size and versatility, this device is ideal for various applications. It features a comprehensive operating system and includes GPIO pins, making it compatible with a wide range of expansion boards for enhanced functionality. Commonly utilized in programming education, smart home automation, Internet of Things projects, creative hardware development, and small embedded systems, the Raspberry Pi is a favorite among electronic enthusiasts and beginners alike. As China-based suppliers and factories continue to embrace this innovative technology, the Raspberry Pi remains a popular choice for anyone looking to dive into the world of electronics and development.

    1. PCB Installation View

    The product PCB measures 265x120 mm, with the top view shown below:

    PCB Installation Overview Layout
    J1 Board-mounted power connector, DC 5–18V J6 HDMI 2.0 connector
    P1 External DC power supply, DC 5–18V J9 2*USB Type-A connectors
    J2 USB Type-C fast charging, up to 20V J10 2*USB Type-A connectors
    Rpi-CM5 Rpi-CM5 Core Board Connector CON1 2*DB9 RS232 connector
    CON3 WAN (4G/5G) module connector A1/A4 SMA board external antenna connector
    J15 Nano-SIM card connector A2/A3 IPEX4-G1 board-mounted antenna connector
    J4 CR2032 battery connector SW1 System power switch button + CM5 indicator light
    J5 CM5 Fan Connector D31 WAN module indicator light
    J3 Firmware update jumper D28 User-defined indicator light
    J8 6 GB switch Ethernet port D3 Power supply status indicator light
    J7 GB LAN Ethernet Connector

    2. Module Installation

    2.1 Pre-Installation Notes

    Note 1: Before installing any modules, ensure the motherboard is powered off. This product does not support hot-plugging for module installation.
    Note 2: Wear anti-static gloves and never install the device with bare hands to prevent static electricity from damaging the motherboard or module chips.

    2.2 Install Rpi-CM5

    Installation: Align the Rpi-CM5 module with the installation slot and place it flat. Gently press the module with your hand to ensure it sits properly in place. Avoid applying excessive force or forcing it down, as this may damage the connector or module. For permanent use, secure all four screw holes with M2.5 screws to prevent detachment during operation.

    Disassembly: Remove the four fixing screws. Using a plastic pry tool, gently pry one edge not in contact with the connector (preferably the right side as shown in the view, i.e., the position of the fan connector), then lift it slightly upward until the module detaches from the slot; remove the module.

    2.3 Install the WAN module

    This product supports standard WWAN modules measuring 30x51mm or 30x42mm, featuring an M.2 B-Key interface with 67 pins and USB 3.0 communication.

    The motherboard typically comes pre-installed with 30x51 modules. If users require 30x42mm modules, a 3.0mm-high M3 single-head fastening stud must be added to the board.

    The user inserts the module at an angle into the M.2 slot. Once in position, gently press the module against the fixed hole for alignment, then secure it with M2.5 screws (M3 for 30x42 models).

    2.4 Install the antenna

    This product features two sets of antennas—one internal and one external. The internal interface uses IPEX-G1, while the external interface employs SMA (internal hole). Users can install the appropriate antenna based on their specific requirements.

    (1) Install the CM5 WiFi and Bluetooth antennas: If the CM5 supports WiFi+BT functionality, a corresponding antenna must be installed. The user should purchase an IPEX-G1 to IPEX-G1 conversion antenna, inserting one end into the CM5's IPEX socket and the other end into the A2 or A3 connector on the board.

    (2) Install the WAN module antenna: WWAN module antennas typically come in one or more units, but this product supports up to two. The WWAN module connectors are usually IPEX-G4 or IPEX-G1; users must purchase the corresponding adapter cable (IPEX-G4 to IPEX-G1 or IPEX-G1 to IPEX-G1) based on the module's antenna interface, and plug both ends of the adapter into the module's antenna connector and the internal A2 or A3 connector, respectively.

    (3) External antenna on the installation panel: The external antenna should be selected based on the user's specific requirements—for example, whether it's a WiFi+BT antenna or a WAN 4G/5G antenna—since their power amplification capabilities differ accordingly. However, the antenna interface must be an SMA internal pin. Insert the antenna into the external antenna connector A1 or A4 and secure it firmly.

    2.5 Install the SIM card

    The SIM card is primarily designed to work with a WAN module for mobile communication. The SIM card slot is located at edge J15 on the board. This product only supports Nano-SIM cards.

    Insertion: Insert the SIM card chip with its edge facing downward and the notch facing inward into the J15 slot, then gently push it inward until you hear the locking sound.

    Remove: The user gently pushes inward with their hand until the unlock sound is heard; the SIM card then pops out and can be removed.

    2.6 Install the real-time clock button battery

    This product provides a 2032 button battery connector (J4) to maintain the real-time clock operation of the Rpi-CM5.

    Installation: The user should purchase a 2032 button battery of the appropriate model. Insert the battery according to the spring orientation, push it toward the locking position, and gently press downward until the battery engages with the locking mechanism.

    Removal: Gently press the battery with your hand, then use a pliers to pull the retaining tab backward until the battery pops out of the socket; remove it.

    Important Battery Warnings:
    • Do not install or remove the battery while the device is powered on.
    • Always hold the battery firmly when handling it vertically, and never drop it onto other components to prevent short circuits.
    • Before installing or removing any modules, remove the button batteries first.

    3. Power Supply and On/Off Operation

    3.1 Power Supply Method

    The product supports three power supply methods:

    (1) Off-panel DC power supply: The external DC power supply can power the product through the P1 DC socket, supporting voltages of 5–18 V DC, with the plug core serving as the positive terminal and the outer ring as the negative terminal. If the external voltage exceeds 20 V, the system will enter a protection mode and automatically cut off the power supply.

    (2) DC power supply within the panel: The J1 on the board is a VH (3.96) connector, providing an in-board DC power supply for interconnection and fully connected to P1. Its functionality and overvoltage protection are identical to those of the external DC power supply. Therefore, users must choose either the external or internal DC power supply method.

    (3) USB Type-C Smart Fast-Charging Power Supply: The product supports power supply via J2 USB Type-C, with an input voltage range of 4V to 20V. It is compatible with PD3.2 EPR, AVS, PPS, SPR, and BC1.2 fast charging protocols, and features a built-in overvoltage protection module.

    (4) Choice between DC power supply and USB Type-C power supply: The product supports both DC and USB Type-C power supplies simultaneously. The system automatically selects the higher-voltage source to provide power based on the voltage levels.

    3.2 Power-on of the System

    Before powering on, users should correctly insert all modules, ensure the PCB is installed inside the fixed chassis or placed in a secure position, and verify that no other cables or components that may cause short circuits are present nearby. Connect a DC power source or a USB Type-C power source.

    3.3 Power Off System

    The user unplugs the external power source, including a DC power supply or a USB Type-C power adapter.

    Note: When debugging the product and inserting or removing various modules or components—particularly the Rpi-CM5 module—you must first remove the button battery; failure to do so may cause a short circuit, potentially rendering the module nonfunctional.

    4. Power On and Off

    4.1 Power On

    After powering on the system, it will start automatically.

    When the system is powered on but in the shutdown state, press SW1 once to power it up.

    After turning on the device, you should normally see the D3 light illuminate.

    4.2 Power Off

    When the system is operating normally, users should first perform a shutdown operation in the system (e.g., the poweroff command), after which the system will shut down automatically.

    Users can press the SW1 switch button once; the system will then display shutdown options, allowing them to choose to shut down.

    Under special circumstances, users can perform a forced shutdown by pressing the SW1 switch button for 3 to 5 seconds.

    After shutting down, the user can unplug the power supply.

    Warning: Do not remove or disconnect the power supply while the system is running. This will cause the writing operation to fail, result in data loss, and may even lead to storage system failure and inability to start properly.

    5. Burn the Firmware

    When your Rpi-CM5 is a brand-new motherboard with no pre-installed system on its internal storage, you must first flash the firmware.

    (1) Preparations before burning: This system uses a Windows host; users should first download the required software and prepare a data cable.

    • Download and install: rpiboot
    • Download and install: Raspberry Pi Imager
    • Data cable: A USB Type-A to USB Type-C data cable.

    (2) Jumper wire: When the power is off, set the jumper at position J3 to a short-circuit state by fitting the jumper cap.

    (3) Insert a DC power supply: Since the USB Type-C bus handles both power supply and data communication, the computer's output power is limited and may not be sufficient to power the Rpi-CM5. Therefore, a DC power supply is recommended.

    (4) Connect the USB cable: Insert the Type-C data cable's Type-C port into the product's J2 USB Type-C connector, and connect its Type-A port to the computer. After insertion, a new device named "BCM2712D0 Boot" appears in Device Manager under General Serial Bus Devices.

    (5) Create a high-capacity USB storage device: Run "rpiboot – Mass Storage Gadget" from the rpiboot installation directory to initialize the previously identified USB device as a high-capacity storage device.

    (6) Burn the firmware: Run Raspberry Pi Imager, follow the prompts to enter the required information, and flash the firmware. Since flashing the firmware may require a lengthy online download process, users can first download the corresponding firmware from their local image repository and then proceed with local firmware import for flashing. For the specific programming and flashing method, refer to the Raspberry Pi documentation until the process is complete.

    (7) Return to normal operating mode: After completing the burning, power off and set the jumper at position J3 to open circuit, or remove the jumper cap. After power restoration, the system will officially operate from the CM5 storage device.

    6. Relevant System Configuration

    6.1 Features that do not require configuration by default

    In this system, the following functions do not require configuration:

    • Switching Function: By default, the switching chip operates normally once properly powered.
    • HDMI functionality: Once the system is operating normally, the HDMI function works properly without requiring any additional configuration.
    • USB-HUB functionality: Once the system is operational, it automatically detects the USB-HUB feature, enabling all four sets of USB Type-A ports to function properly.

    The features to configure include:

    • LAN port functionality: The Rpi-CM5 cannot automatically recognize the YT6801 chip in this product and requires driver installation.
    • RS232 port functionality: The Rpi-CM5 does not default enable the corresponding UART function; kernel DTS configuration is required.
    • The required GPIOs for the system necessitate modifying the kernel DTS or performing corresponding configurations.

    6.2 Pre-configuration Preparation

    After properly powering on the device, first configure its WiFi function to establish network connectivity—ideally enabling internet access.

    sudo systemctl enable ssh
    sudo systemctl start ssh

    6.3 Install the LAN Port Driver

    This product's LAN port (J7) employs the YT6801 chip and connects via the PCIe 2.0 interface of the Rpi-CM5 board.

    Upon entering the system, using the lspci command reveals the device: 0001:01:00.0 Ethernet Controller: Motorcomm Microelectronics YT6801 Gigabit Ethernet Controller (Rev 01). This indicates that the YT6801 is connected via a PCIe interface and requires only driver installation.

    Installation and deployment steps:

    (1) Copy driver: yt6801-1.0.31.tar.gz to product directory
    (2) Decompress driver: tar xvf yt6801-1.0.31.tar.gz
    (3) Enter directory: cd yt6801-1.0.31
    (4) Install driver: sudo ./install_yt6801-driver
    (5) Verify complete without error prompts

    Writing the MAC address: If you need to write the MAC address to the network card, follow these steps:

    1. cd yt6801-1.0.31
    2. Check that Motorcomm_NIC_Burn_Helper exists
    3. sudo ./Motorcomm_NIC_Burn_Helper -index 0 -mac "MAC-ADDR"

    Parameter declaration:
    • Index 0: The 0th device. This product has only one device, so it can only be 0.
    • -mac "MAC-ADDR": Specifies the written MAC address, which can be separated by a '-' or ':' symbol.

    Caution: A MAC address can only be written once. Use it carefully and ensure you write the correct address.

    6.4 Configure DTS Functionality

    Modify the /boot/firmware/config.txt file and add a line in Section [CM5]:

    Add row Use
    dtoverlay=uart1-pi5
    dtparam=uart1=on
    Configure UART1
    Open UART1
    dtoverlay=uart2-pi5
    dtparam=uart1=on
    Configure UART2
    Open UART2
    dtoverlay=spi4-1cs Configure SPI4
    dtoverlay=gpio-fan Enable Fan Control
    dtoverlay=act-led Configure Activity LED
    dtoverlay=gpio-shutdown,gpio_pin=17,active_low=1,gpio_pull=up Power monitoring, automatic shutdown
    gpio=0-7=a2 Configure GPIO 0-7 as the second function group
    gpio=14,15=op,dh WWAN AWREN and WWAN WDIS are configured to output a high level.
    gpio=16=op,dl The User_LED is configured to output a low level.
    gpio=17-21=ip PWR_GOOD, USBPn OC# configured as input
    gpio=22-27=pu
    gpio=22-27=ip
    The LINK status indicator for switch ports (P1–P6) is set to high.
    The LINK status indicator for switch ports (P1–P6) is configured as input.

    Frequently Asked Questions (FAQ)

    Q What power input specifications does this carrier board support?
    The board supports dual power input options: a standard DC power source (via DC socket P1 or internal VH connector J1) providing DC 5–18V with overvoltage protection cutting off above 20V, and a USB Type-C port (J2) supporting 4V–20V fast-charging protocols (PD3.2, PPS, BC1.2). If both are plugged in, the system automatically uses the source with the higher voltage.
    Q Can I plug or unplug the Raspberry Pi CM5 or WAN modules while the board is running?
    No. The board does not support hot-plugging. Always power down the system, disconnect the power supply cables, and remove the CR2032 button battery before inserting or detaching the CM5 board, WWAN modules, or internal antenna connectors to avoid short circuits.
    Q Why is the Gigabit LAN port (J7) not working after the initial OS installation?
    The LAN port J7 relies on the Motorcomm YT6801 Ethernet chip via the PCIe 2.0 interface, which Raspberry Pi OS does not detect out-of-the-box. You must compile and install the yt6801 kernel driver manually, and optionally write your assigned MAC address using the helper tool.
    Q What form factors and sizes are compatible with the WAN expansion slot?
    The board supports standard M.2 Key-B WWAN modules (67 pins with USB 3.0 lines) in both 30x51mm and 30x42mm dimensions. The board is pre-configured for 30x51mm modules; adapting a 30x42mm card requires an additional 3.0mm-high M3 fastening stud.
    Q How do I properly flash or burn firmware to the CM5 eMMC storage?
    Short the J3 jumper with a jumper cap while powered off, power the carrier board using an external DC supply, connect the J2 Type-C port to your computer, and run rpiboot to mount the onboard storage as a mass storage device. Then write the OS using Raspberry Pi Imager. Once finished, remove the J3 jumper cap before rebooting.
    Q What is the correct procedure for shutting down the board?
    Execute a software shutdown command (such as sudo poweroff) or press the SW1 power button once to initiate an orderly OS shutdown. Alternatively, a forced hardware power-off can be initiated by holding SW1 for 3 to 5 seconds. Never remove the power cable abruptly during active disk writing.

    Send Inquiry